История страницы

To test the robot's operation and correct actions, you need to run the robot scheme in ROBIN Studio in debug mode. The debug mode control panel is located at the top of the workspace:

Image Added

Buttons for interacting with the robot scheme on the control panel:

Button symbol	Name	Action
Image Added	Save results	If this checkbox = true is selected, the results of the scenario startup are saved. After the first run, this makes it possible to start the scenario from any action in the robot scheme in subsequent runs
Image Added	Start	Starts debug mode from the very first action in the scheme
Image Added	Pause	Pauses the robot after an action that was running when the "Pause" button was clicked. You will need to click either the "Start" or "Step Forward" button to continue. It is also possible to stop the execution of a scenario. The button becomes active only after the robot is started
Image Added	Stop	Stops robot execution and exits debugging mode. The button is active while the robot is running
Image Added	Soft stop	The stop will only occur if the user clicks the "Soft Stop" button during debugging. The results produced by the robot up to the soft stop point are saved. Otherwise, there will be no stop at the marked action. The button is active while the robot is running
Image Added	Hard stop	Stops robot execution and exits debugging mode, interrupting the execution of actions. The results are not saved. The button is active while the robot is running
Image Added	Restart	Starts debugging mode from the first action. The button is active in debug mode
Image Added	Step forward	Executes the action before which the scheme was paused and sets the debugging mode to pause. Active in debugging mode
Image Added	Track on debug	When this flag is checked, the progress of the script execution is displayed as a green frame on the action that is currently being executed. The frame is displayed while the scheme is paused
Image Added	Robot launch options	When you click the button, the "Robot launch options" window opens, where you can select the logging level and set the values of the robot input parameters, if necessary

Before starting the robot in debug mode, you can select the necessary logging level by clicking on theImage Added button, selecting the necessary logging level, and clicking "Save":

Image Added

If you click the "Cancel" button, the logging level will not be saved and you will return to the ROBIN Studio workspace.

To start debugging the robot scheme, click the "Start" button on the Studio debugging panel.

If the scheme is not started in debugging, or if the "Stop" button was clicked during operation, the debugging panel is grayed out. The control panel will be colored green when the robot is running, and yellow when it is paused:

Image Added

Image Added

Image Added

After starting the scheme, the debugging level logging starts.

The action log is located at the bottom of ROBIN Studio and looks as follows:

Image Added

After termination of the robot, the robot action log is available to the user. When the scheme is restarted, the action log in ROBIN Studio is cleared

ожидается перевод от Анны

добавлены английские скрины

Image Removed

Кнопки взаимодействия со схемой робота на панели управления:

...

Иконка

...

Название

...

Действие

...

...

...

...

...

...

...

...

Перезапуск

...

Запускает режим отладки с экшена, выделенного в данный момент на схеме.. Активна в режиме отладки.

...

...

...

Параметры запуска робота

...

При нажатии кнопки открывается окно "Параметры запуска робота", где имеется возможность выбора логирования.

Для запуска робота в режиме отладки необходимо выбрать нужный уровень логирования, для этого необходимо нажать
на кнопку Image Removed, выбрать нужный уровень логирования, и нажать "Сохранить":

Image Removed

При нажатии кнопки "Отмена", уровень логирования не сохранится, и произойдет возврат в рабочее пространство ROBIN Studio.

Далее схема запускается в ROBIN Studio после нажатия кнопки "Старт".

При работе робота панель по управлению режимом отладки будет окрашиваться в зеленый цвет,
при паузе - в желтый цвет. Если схема не была запущена, либо во время работы была нажата кнопка "Стоп", панель будет окрашена в серый цвет:

Image Removed

Image Removed

Image Removed

После запуска схемы, стартует запись лога уровня отладки.

Лог действий находится в нижней части ROBIN Studio и выглядит следующим образом:

Image Removed

После завершения работы робота, пользователю доступен лог действий робота, при повторном запуске схемы лог действий в ROBIN Studio обнуляется.